Kin Ngố
26-05-2011, 09:29 AM
Cleaning the Guestroom
Figture : Making a bed using the mitered corner . Tuck in the top sheet and blanket across the foot of the bed with the sides hanging free(a) . Pick up the sheet and blanket together at about a 45-degree angle and place right against the side of the bed (b) . Tuck the bottom selvage under the mattress while still holding up the top at a 45-degree angle(c) . Allow the top pf fall and then smooth it (d) . Tuck the sile under the mattress (e) . Depending on company policy, the sides could be left hanging down . The bottom sheet should also be mitered by itself at the head of the bed .
Leave both sides untucked . When sides are tucked in, the guests will more than likely “ unmake” the bed when they try to get into it . As top sheed and banked are pulled back , the bottom sheet become untucked also .
This writer suggests the best of the both methods . Tuck in the top sheet and blanked on the sides of the bed opposite to the side the guest is more likely to use when entering the bed. Leave the side that the guest will most likely use to enter the bed untucked .
The bedspread . Because the bed is most often the major focal point of the guestroom , the bedspread must be properly positioned , smoothed , and without lumps upon completion of the makeup. Assuming the spread is properly fitted , it should just miss touching the floor on three sides and be properly tucked in at the head of the bed . The corners of the spread at the foot of the bed should either be tucked or pleated .
The spread at the head of the bed is easily dressed by firstturning the spread back about 12 inches from the headboard . The pillows should be place about 15 inches from the headboard on top of the turned-back spread . Once done , the front edge of the spread can be carried back over the pillows on both sides can be carried back over the pillows on both sides of the bed , and thenthe entire until can be rolled together towardthe headboard . Figure 10.17 shows the GRA turning back the pread about 10 inches from the head of the bed in preparation for rolling the pillows as a unit .
Figture : Making a bed using the mitered corner . Tuck in the top sheet and blanket across the foot of the bed with the sides hanging free(a) . Pick up the sheet and blanket together at about a 45-degree angle and place right against the side of the bed (b) . Tuck the bottom selvage under the mattress while still holding up the top at a 45-degree angle(c) . Allow the top pf fall and then smooth it (d) . Tuck the sile under the mattress (e) . Depending on company policy, the sides could be left hanging down . The bottom sheet should also be mitered by itself at the head of the bed .
Leave both sides untucked . When sides are tucked in, the guests will more than likely “ unmake” the bed when they try to get into it . As top sheed and banked are pulled back , the bottom sheet become untucked also .
This writer suggests the best of the both methods . Tuck in the top sheet and blanked on the sides of the bed opposite to the side the guest is more likely to use when entering the bed. Leave the side that the guest will most likely use to enter the bed untucked .
The bedspread . Because the bed is most often the major focal point of the guestroom , the bedspread must be properly positioned , smoothed , and without lumps upon completion of the makeup. Assuming the spread is properly fitted , it should just miss touching the floor on three sides and be properly tucked in at the head of the bed . The corners of the spread at the foot of the bed should either be tucked or pleated .
The spread at the head of the bed is easily dressed by firstturning the spread back about 12 inches from the headboard . The pillows should be place about 15 inches from the headboard on top of the turned-back spread . Once done , the front edge of the spread can be carried back over the pillows on both sides can be carried back over the pillows on both sides of the bed , and thenthe entire until can be rolled together towardthe headboard . Figure 10.17 shows the GRA turning back the pread about 10 inches from the head of the bed in preparation for rolling the pillows as a unit .